While I haven’t quite finished my previous (or should I say current) project – Pinbot, a new project popped up a few weeks ago that felt like a good opportunity – so I grabbed it. This time, I’ll be looking at a Counterforce machine by Gottlieb. It’s part of the Star 80 series and was released back in 1980. This particular machine started life in Italy, before being imported here to Australia. I was attracted to it as the gameplay looks kind of neat – seems like a mash of missile command and space invaders played out on a pinball playfield. Plus it’s an opportunity to work on a System 80 machine, which is something I’ve not yet done – so it should be an interesting experience. My last few projects have been restorations where I’ve spent a bit of money doing them up. But this project will be a little different. Due to the damage on the playfield, the machine won’t gain much value with everything else restored around it. The detail in the artwork makes it impossible to paint or touch up. Therefore, my plan is to keep spending limited. Any worn or damaged parts considered important will be replaced (globes, rubbers, broken drop targets, coil sleeves, etc). Anything that is still usable will be cleaned up and put back into the machine. So the goal here is to service all parts of the the machine, clean it up (wow does it need a clean) and repair anything broken to make it a fully functional game once again. I’ve set myself a reasonable budget to prevent over capitalising on it, but I may run into some nasty surprises along the way. So we’ll see how that turns out 🙂
Continue Reading
service
All posts tagged service
The final part covering my 12 month service of my Nugent. In some respects, it’s getting a much better playfield clean than when I rebuilt it this time last year. Although I replaced many old and worn parts, I didn’t give enough attention to the surface of the playfield. It was wiped down but I didn’t have the knowledge or confidence at the time to do more. The apron area has been taken care of, as has the lower playfield area. Now on to the upper half. First step was to remove everything. This includes the rebound rubber and gates. There is quite a bit of crap built up already.
The 12 months service of my Nugent machine continues. First up, I’ll expand on the area of the playfield which is largely responsible for spreading crap around the machine. At the top of the playfield there is a large wear patch that extends for about 10cm between the bonus saucer and the multiplier drop targets. This area seems to be a common wear zone as I’ve seen other Nugent playfields with damage in this area (although the others have not been as bad as this).
An area of the playfield I’ve been looking forward to working on is the mini playfield and the pop bumpers that live beneath it. I’ll also take the opportunity here to look at the bank of 5 stationary targets that sit just to the left of the pop bumpers. It’s going to be a long update I think and lots of photos to look through. So hopefully you hang in until the end 🙂 The starting point is good. All plastics and posts are there. The mini playfield itself is in one piece, although I can see some small cracks at a few point that will need to be looked at.
Playing pinball is fun and it’s something people of all ages can partake in and enjoy. For me, learning how the machines work and getting your hands on the parts that make the games tick take it to a whole new level. In fact I spend more time with my hands on parts than I do on the flipper buttons.
When I was working on that first machine back in January and February, I often found the process very stop-start. In part, this was due to my inexperience with pinball machines and not really being able to plan what I was actually going to need (or being aware of what was available). I kept finding myself held up while trying to source random parts. Certain screw types, nuts, plates, frames, wires, housings, bulbs, etc. Some were easy to source while others more obscure and no real part number to reference. I experienced it again (although to a lesser degree) when working on my Fireball Classic. In most cases the part (or a suitable alternative) were sourced thanks to various sellers or through wanted posts on Aussie Arcade. I decided part way through the Fireball I was going to somehow source a pile of random spare parts from different machines which would help aid me with future repairs / rebuilds.
Enter the “crap box” (or boxes now that I’ve picked up a few). I found these boxes irresistible. Like a big box filled with lucky dip prizes. Some will be cool. Others will be.. well.. crap. Who knows what I’ll score – it brings excitement 🙂 In this first example, I have a 15kg box of random parts that cost $6.60.
